View AUIPS6041G_7655857.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

march, 1 2 th 2012 automotive grade au ips6041(g)(r)(s) www.irf.com 1 intelligent power high side switch features ? over temperature shutdown (with auto - restart) ? short circuit protection (current limit) ? reverse battery protection (turns on the mosfet) ? full diagnostic capability (short circuit to battery) ? active clamp ? open l oad detection in on and off state ? ground loss protection ? logic ground isolated from power ground ? esd protection ? lead free and rohs compliant description the au ips6041(g)(r)(s) is a five terminal intelligent power switch (ips) for use in a high side configu ration. it features short circuit, over - temperature, esd protection, inductive load capability and diagnostic feedback. the output current is limited to the ilim value. the current limitation is activated until the thermal protection acts. the over - tempera ture protection turns off the device if the junction temperature exceeds the tshutdown value. it will automatically restart after the junction has cooled 7c below the tshutdown value. the reverse battery protection turns on the mosfet. a diagnostic pin pr ovides different voltage levels for each fault condition. the double level shifter circuitry will allow large offsets between the logic and load ground. product summary rds(on) 130m ? max. vclamp 39v i limit 7a open load 3 v / 0.22a packages so8 d - pak au ips 6 041g au ips6041r to220 d2pak au ips 6 041 au ips6041s typical connectio n control rin load +bat input signal v diag rdgs pull - up resistors required for open load off and short circuit to vbat detection rdgp +5v out(4) dg(3) vcc(5 - 6 - 7 - 8) in(2) gnd(1)
au ips6041(g)(r)(s) www.irf.com 2 qualification information ? qualification level automotive (per aec - q100 ?? ) comments: this family of ics has passed an automotive qualification. irs industrial and consumer qualification level is granted by extension of the higher automotive level. moisture sensitivity level d2pak - 5l msl1, 260c (per ipc/jedec j - std - 020) to - 220 not applicable (non - surface mount package style) dpak - 5l msl1, 260c (per ipc/jedec j - std - 020) soic - 8l msl2, 260c (per ipc/jedec j - std - 020 ) esd machine model class m2 (+/ - 150v) ??? (per aec - q100 - 003) human body model class h1c (+/ - 1500v) ??? ( per aec - q100 - 002 ) charged device model (soic, dpak,d2pak) class c 4 (+/ - 900v) ??? (per aec - q100 - 011) charged device model (to220) class c 3b (+/ - 750 v) ??? (per aec - q100 - 011) ic latch - up test class ii , level a (per aec - q100 - 004) rohs compliant yes ? qualification standards can be found at international rectifiers web site http://www.irf.com/ ?? exceptions to a ec - q100 requirements are noted in the qualification report. ??? passing voltage level
au ips6041(g)(r)(s) www.irf.com 3 absolute maximum ratings absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. all voltage parameters are referenced to grou nd lead. tj= - 40c..150c, vcc=6..35v ( unless otherwise specified). symbol parameter min. max. units vout maximum output voltage vcc - 35 vcc+0.3 v voffset maximum logic ground to load ground offset vcc - 35 vcc+0.3 vin maximum input voltage - 0.3 5.5 vc c max. maximum vcc voltage ? ? ? ? 1sqrt. footprint ? thermal characteristics symbol parameter typ. max. units rth1 thermal resistance junction to ambient au ips6041g 100 ? c/w rth1 thermal resistance junction to ambient au ips6041r d - pak std. footprint 70 ? rth2 thermal resistance junctio n to ambient au ips6041r d - pak 1 sqrt. footprint 50 ? rth3 thermal resistance junction to case au ips6041(r)(s) d - pak/d2pak/to220 6 ? rth1 thermal resistance junction to ambient au ips6041(s) d2pak/to220 std. footprint 60 ? rth2 thermal resistance ju nction to ambient au ips6041s d2pak 1 sqrt. footprint 40 ? recommended operating conditions these values are given for a quick design. for operation outside these conditions, please consult the application notes. symbol parameter min. max. units vih h igh level input voltage 4 5.5 vil low level input voltage 0 0.9 iout continuous drain current, tambient=85c, tj=125c, vin=5v a rth=100c/w au ips6041g ? 1 sqrt. footprint ? 2.3 rin recommended resistor in series with in pin 4 10 k ? 20 rol recommended pull - up resistor for open load detection 5 100 f max. max. switching frequency ?
au ips6041(g)(r)(s) www.irf.com 4 static electrical characteristics tj= - 40c..150 c, vcc= 6..28 v (unless otherwise specified), typical values are given for vcc=14v and tj=25c symbol parameter min. typ. max. units test conditions rds(on) on state resistance tj=25c ? ? ? ? 125 155 vin=5v, iout=1. 5 a on state resistance during reverse battery tj=25c ? 140 180 vcc - gnd= - 14 v vcc op. operating voltage range 6 ? ? ? ? ? ? ? ? ? 4 0 100 a vin=5v idg dg leakage current ? 0.1 10 vdg=5v vdg low level d g voltage ? 0.25 0.4 v idg=1.6ma switching electrical characteristics vcc=14v, resistive load= 6 ? , vin=5v, tj= - 40c.. 150 c , typical values are given for tj=25c symbol parameter min. typ. max. units test conditions tdon turn - on delay time ? ? ? ? ? ? 100 ? ? ? ? ? ? 50 ?
au ips6041(g)(r)(s) www.irf.com 5 protection characteristics tj= - 40c..150c, vcc=6..28 v (unless otherwise specified), typical values are given for vcc=14v and tj=25c symbol parameter min. typ. max. units test conditions ilim internal current limit 4 7 10 a vout=0v , tj=25c tsd+ over temperature high threshold 150(1) 165 ? ? ? ? ? true table operating conditions in out dg normal h h h normal l l h open load h h l open load (3) l h l short circuit to gnd h l l short circuit to gnd l l h short circuit to vcc h h l (4) short circuit to vcc (5) l h l over - temperature h l l over - temperature l l h (3) with a pull - up resistor connected between the output and vcc. (4) vds lower than 10mv. (5) without a pull - up resistor connected between the output and vcc. lead assignments
au ips6041(g)(r)(s) www.irf.com 6 functional block diagram all values are typical in vcc out 37v driver i limit 43v 150k ? i sense - + charge pump level shifter tj 165c 158c 2.5v 2.0v 6 v dg 6 v gnd ground disconnect 3v - + open load off over - temp 20mv - + open load on 3v - + short circuit 43v vcc - gnd >uv
au ips6041(g)(r)(s) www.irf.com 7 figure 1 C active clamp waveforms figure 2 C protection timing diagram figure 3 C switching times definitions figure 4 C active clamp test circuit vds ids vin vcc vds clamp t clamp see application notes to evaluate power dissipation tj ilim tsd+ tsd - iout vin limiting thermal cycling dg vout vin tr - in 90% 10% 90% 10% td on tr1 td off tf vcc - 5v tr2 vcc vclamp iout vin in vcc out r l 0v 5v 14v + - vout rem : during active clamp, vload is negative dg gnd
au ips6041(g)(r)(s) www.irf.com 8 tj, junction temperature (c) figure 6 - normalized rds(on) (%) vs tj (c) figure 7 C max. output current (a) vs load inductance (mh) load inductance (mh) iout, output current (a) figure 8 C max. ouput current (a) vs ambient temperature (c) ids, cont. output current (a) tamb, ambient temperature (c) figure 5 C switching energy ( j) vs output current (a) eon, eoff, switching energy (j) iout, output current (a) rds(on), drain - to - source on resistance (normalized) eon eoff 50% 100% 150% 200% -50 0 50 100 150 0 0.5 1 1.5 2 2.5 3 -50 0 50 100 150 100c/w 0 50 100 150 200 250 300 0 1 2 3 4 5 0.1 1 10 0.1 1 10 100 1000
au ips6041(g)(r)(s) www.irf.com 9 figure 10 C i limit (a) vs junction temperature (c) i limit (a) zth, tra nsient thermal impedance (c/w) time (s) tj, junction temperature (c) vcc, power supply voltage (v) icc on/ icc off, supply current (a) figure 11 C icc on/ icc off (a) vs vcc (v) * figure 12 C icc on/ icc off (a) vs tj (c) * icc on/ icc off, supply current (a) tj, junction temperature (c) * vout connected to groun d with r< 4 ? figure 9 C transient thermal impedance (c/w) vs time (s) 0 2 4 6 8 -50 0 50 100 0.01 0.1 1 10 100 1e-5 1e-4 1e-3 1e-2 1e-1 1e+0 1e+1 1e+2 1e+3 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 0 5 10 15 20 25 30 icc on icc off 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 -50 0 50 100 150 icc on icc off
au ips6041(g)(r)(s) www.irf.com 10 case outline C so8
au ips6041(g)(r)(s) www.irf.com 11 tape & reel - so8
au ips6041(g)(r)(s) www.irf.com 12 case outline - to220 (5 lead s )
au ips6041(g)(r)(s) www.irf.com 13 case outline 5 lead s - d2pak
au ips6041(g)(r)(s) www.irf.com 14 tape & reel 5 lead s - d2pak
au ips6041(g)(r)(s) www.irf.com 15 case outline 5 lead s C dpak
au ips6041(g)(r)(s) www.irf.com 16 tape & reel 5 lead s C dpak
au ips6041(g)(r)(s) www.irf.com 17 part marking information
au ips6041(g)(r)(s) www.irf.com 18 ordering information base part number package type standard pack complete part number form quantity auips6041 to220 - 5 - leads tube 50 auips6041 auips6041s d2 - pak - 5 - leads tube 50 auips6041s tape and reel left 800 auips6041strl tape and reel right 800 auips6041strr aui ps6041r d - pak - 5 - lead s tube 75 auips6041r tape an d reel 2000 auips6041rtr tape and reel left 3000 auips6041rtrl tape and reel right 3000 auips6041rtrr AUIPS6041G soic - 8 tube 95 AUIPS6041G tape and reel 2500 AUIPS6041Gtr
au ips6041(g)(r)(s) www.irf.com 19 important notice unless specifically designated for the automotive market , international rectifier corporation and its subsidiaries (ir) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. part numbers designated with the au prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. all products are sold subject to irs terms and conditions of sa le supplied at the time of order acknowledgment. ir warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with irs standard warranty. testing and other quality control techniques are used to the extent ir deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ir assumes no liability for applications assistance or customer product design . customers are responsible for their products and applications using ir components. to minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. reproduction of ir information in ir dat a books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alterations is an unfair and deceptive business p ractice. ir is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ir products or serviced with statements different from or beyond the parameters stated by ir for t hat product or service voids all express and any implied warranties for the associated ir product or service and is an unfair and deceptive business practice. ir is not responsible or liable for any such statements. ir products are not designed, intended , or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of t he ir product could create a situation where pe rsonal injury or death may occur. should buyer purchase or use ir products for any such unintended or unauthorized application, buyer shall indemnify and hold international rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ir wa s negligent regarding the design or manufacture of the product. ir products are neither designed nor intended for use in military/aerospace applications or environments unless the ir products are specifically designated by ir as military - grade or enhance d plastic. only products designated by ir as military - grade meet military specifications. buyers acknowledge and agree that any such use of ir products which ir has not designated as military - grade is solely at the buyers risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. ir products are neither designed nor intended for use in automotive applications or environments unless the specific ir products are designated by ir as co mpliant with iso/ts 16949 requirements and bear a part number including the designation au. buyers acknowledge and agree that, if they use any non - designated products in automotive applications, ir will not be responsible for any failure to meet such re quirements. for technical support, please contact irs technical assistance center world headquarters: 101 n sepulbeda blvd., el segundo, california 90245 tel: (310) 252 - 7105
au ips6041(g)(r)(s) www.irf.com 20 revision history revision date notes/changes c februrary, 28th 2009 au number update d march, 1 4th 2011 au release f may 15, 2012 add the test condition for the icc ( off ) parameters

▲Up To Search▲

Price & Availability of AUIPS6041G

	To Download AUIPS6041G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .